Electrical Engineering Design Services for U.S. Architecture Firms

National MEP Engineers is a provider of electrical engineering and design services in the United States. Our services range from early load strategy and system zoning to power distribution, lighting, standby power, and arc flash analysis. We validate every deliverable with fault-current and load-balancing studies prior to producing a drawing, followed by coordination in BIM with mechanical and plumbing.

Verified By

US-licensed PEs

Base Codes

NEC + state & local amendments

Analysis

Fault current, arc flash, load balancing

Deliverable

Full-scope engineering through permit & closeout

Coverage

20 states

Support

Utility & AHJ coordination

Electrical Engineering Design Services for U.S. Architecture Firms

National MEP Engineers is a provider of electrical engineering and design services in the United States. Our services range from early load strategy and system zoning to power distribution, lighting, standby power, and arc flash analysis. We validate every deliverable with fault-current and load-balancing studies prior to producing a drawing, followed by coordination in BIM with mechanical and plumbing.

Verified By

US-licensed PEs

Base Codes

NEC + state & local amendments

Analysis

Fault current, arc flash, load balancing

Deliverable

Full-scope engineering through permit & closeout

Coverage

20 States

Support

Utility & AHJ coordination

What does Electrical Engineering and
Design actually include?

Electrical engineering and design encompass a building’s power distribution, lighting, and life-safety systems. They include elements such as load calculations, single-line diagrams, panel schedules, grounding, arc flash labeling, and standby power strategies.

On the most recent projects, they also extend to EV charging circuits and solar interconnections. National MEP Engineers validates every output with fault-current and voltage-drop analyses, then issues a PE-stamped, NEC-compliant set ready for permit and bid.

What’s in an Electrical Engineering and Design Scope

Our deliverables vary depending on the type of building we are working on. A restaurant’s high-diversity equipment load has very little in common with a multifamily infrastructure’s submetering plan. However, most projects draw from the same primary scope:

  • Lighting plans and lighting control layouts
  • Power distribution and single-line diagrams
  • Panel schedules and load summaries
  • Branch circuits and feeder design
  • Emergency and standby power systems
  • Arc flash hazard analysis and equipment labeling
  • Short circuit and protection device coordination studies
  • Grounding and bonding details
  • EV charging circuit design
  • Solar PV and utility interconnection support
  • Submetering and tenant metering layouts
  • Lighting power density and energy code compliance
  • Low voltage systems coordination
  • Riser diagrams for efficient routing

Where Each Electrical System Carries Its Weight

Seven system groups carry most of the coordination weight on an electrical package:

System

What It Governs

Key Coordination Point

Power Distribution

Feeders, transformers, service entrance

Short circuit ratings, utility capacity

Lighting and Controls

Fixture layout, zoning, photometrics

Ceiling coordination, energy code targets

Panels and Feeders

Branch circuits, load allocation

Spare capacity for tenant growth

Emergency and Standby Power

Generators, ATS, egress lighting

NFPA 110 transfer time, fire alarm tie-in

Arc Flash and Protective Coordination

Incident energy, device settings, labeling

NFPA 70E and OSHA compliance

Grounding and Bonding

Fault protection, equipment safety

Structural steel and utility grounding electrode

EV Charging and Renewable Coordination

Charger circuits, PV tie-in, metering

Utility interconnection agreements, panel capacity

System

What It Governs

Key Coordination Point

Power Distribution

Feeders, transformers, service entrance

Short circuit ratings, utility capacity

Lighting and Controls

Fixture layout, zoning, photometrics

Ceiling coordination, energy code targets

Panels and Feeders

Branch circuits, load allocation

Spare capacity for tenant growth

Emergency and Standby Power

Generators, ATS, egress lighting

NFPA 110 transfer time, fire alarm tie-in

Arc Flash and Protective Coordination

Incident energy, device settings, labeling

NFPA 70E and OSHA compliance

Grounding and Bonding

Fault protection, equipment safety

Structural steel and utility grounding electrode

EV Charging and Renewable Coordination

Charger circuits, PV tie-in, metering

Utility interconnection agreements, panel capacity

From Load Calculation to a Constructable Set

Strategy and Equipment Zoning

Panel locations, standby power, and transformer siting strategy are set, while the floor plan remains flexible enough to accommodate them.

Load Calculations and Circuiting

Branch circuits, panel schedules, and feeder sizing take shape in step with mechanical and structural development.

Fault and Performance Validation

Short-circuit ratings, voltage drop, arc-flash incident energy, and protective device coordination are confirmed prior to permit submission.

Utility and AHJ Support

Utility coordination, responses to AHJ comments, and contractor RFIs follow through to project closeout.

Analysis Before Documentation

Voltage drop issues, feeder sizing concerns, and protective device coordination gaps surface at the desk, long before they can emerge mid-construction.

SKM PowerTools for short-circuit and arc flash analysis

ETAP for protective device coordination

Autodesk Revit for BIM coordination

AutoCAD for 2D documentation

Bluebeam Revu for markup and QC review

AGi32 for lighting and photometric simulation

SKM PowerTools for short-circuit and arc flash analysis

ETAP for protective device coordination

AGi32 for lighting and photometric simulation

Autodesk Revit for BIM coordination

AutoCAD for 2D documentation

Bluebeam Revu for markup and QC review

NEC

NFPA 70E

IEEE 1584

IEEE 1584

ANSI C84.1

Local Utility Standards

AHJ Amendments

NFPA 110

NEC

NFPA 70E

NFPA 110

IEEE 1584

ANSI C84.1

Local Utility Standards

AHJ Amendments

Lasting Protective Benefits of Our
Coordinated Electrical Sets

Decision with Long-Standing Efficiency

We prioritize setting panel configuration in SD and making lighting selections in DD that impact tenant fit-out costs and energy use for years. Trade-offs are modeled while changes are still cost-effective.

Independent, Thorough QC at Every Stage

Our PEs review each deliverable at the close of SD, DD, and CD. This quality-first approach helps catch clashes, omissions, and code gaps when they can still be fixed affordably.

Minimal Field Conflicts and Change Orders

BIM coordination aligns conduit routing and equipment connections with mechanical and plumbing systems before construction work starts on-site, reducing 98% of spatial conflicts and change orders.

 

Fast-Track Delivery, Ready for AHJ Review

We complete fault current, arc flash, and load analysis before submission to ensure the required documentation is ready for faster, more seamless delivery.

Delivering Electrical Engineering in 20 States

National MEP Engineers has delivered successful projects across 19 states and the country's capital.

News & Insights

Human-Centric Lighting in Healthcare: Designing for Wellness, Safety, and Recovery

Has it ever crossed your mind how healthcare facilities’ lighting...

MEP Service Market Growth and Its Effect on Building Design Strategies

At present, the worldwide MEP service market is at a...

Co-Designing with MEP for High-Performance Acoustical Interiors

As you waltz into a well-designed recording studio or office,...

Orlando Matta

Orlando Matta
Owner & Principal Architect

"I'm very satisfied with the response time. The clients feel confident knowing that you have PEs based in the U.S."

Christopher Middleton
Owner & Principal Architect

"We wish we'd found you 25 years ago. It would've made our lives so much easier."

Client Stories

Real results speak louder than any promise we could make. Explore the experiences of the architectural firms we’ve partnered with to scale their production capacity. From overcoming submission challenges to delivering accurate submittals on tight deadlines, see how our team is helping projects cross the finish line and how we can help you do the same. Your project’s success is our biggest win.

Clients' Story

Real results speak louder than any promise we could make. Explore the experiences of the architectural firms we’ve partnered with to scale their production capacity. From overcoming submission challenges to delivering accurate submittals on tight deadlines, see how our team is helping projects cross the finish line and how we can help you do the same. Your project’s success is our biggest win.

Orlando Matta
Owner & Principal Architect

"I'm very satisfied with the response time. The clients feel confident knowing that you have PEs based in the U.S."

Christopher Middleton
Owner & Principal Architect

"We wish we'd found you 25 years ago. It would've made our lives so much easier."

Common Queries of Architects & GCs

Nation MEP Engineers weighs equipment loads, routing paths, code-required clearances, and day-to-day operational needs together to land on locations that are safe, accessible, and compatible with the architectural intent. This early groundwork heads off late-stage relocations that would otherwise disrupt coordination.

Yes, with sheer precision. We assess legacy infrastructure through available plans, site audits where needed, and utility capacity validation. This allows upgrades to be designed that safely integrate with what is already in place.

We contact utility providers early to confirm service capacity, transformer locations, and interconnection requirements. Our team responds to AHJ comments promptly with code references, load calculations, and clarifications, all under the guidance of a PE's interpretation of the NEC and applicable local amendments.

Coordination takes place in BIM, where equipment connections, conduit routers, and electrical clearances are aligned with piping, mechanical ductwork, and architectural elements prior to construction.

Yes, absolutely. We first plan load diversity, spare capacity, and panel allocation, so extra circuits or equipment can be added later without a comprehensive system reconfiguration.